[restoration] L319D - 1958 - Seite 5 - L319-forum.de  

[restoration] L319D - 1958

Bilder und Beschreibungen von Restaurierarbeiten oder auch selbstherstellen von Ersatzteilen oder Werkzeugen. Sowie Tipps und Tricks die das Arbeiten erleichtern
Antworten
Benutzeravatar
panzerjim
Beiträge: 222
Registriert: 19.04.2015, 07:14
Wohnort: Bretagne (France)
Kontaktdaten:

Re: [restoration] L319D - 1958

Beitragvon panzerjim » 26.09.2016, 05:46

let's continue playing with old dry grease, rust, sand, etc .....

front suspension before ...

Bild

.... and after cleaning and painting :

Bild

before - after :

Bild

Bild

steering bar :

Bild

cleaning all little pieces with pressurized air and rag :

Bild

always cleaning and painting :

Bild

rest of the front axe : :)

Bild

like new ! :D

Bild

it feels good to move forward!

see you !
we can't make new with old .... but we try 8)

Benutzeravatar
Compay
Beiträge: 948
Registriert: 24.08.2004, 11:44
Wohnort: holland

Re: [restoration] L319D - 1958

Beitragvon Compay » 26.09.2016, 09:16

du super travail

what paint do you use?
RX5 RX10 ?

des beaux jours!

Benutzeravatar
Compay
Beiträge: 948
Registriert: 24.08.2004, 11:44
Wohnort: holland

Re: [restoration] L319D - 1958

Beitragvon Compay » 26.09.2016, 09:17

du super travail

what paint do you use?
RX5 RX10 ?

des beaux jours!

Benutzeravatar
panzerjim
Beiträge: 222
Registriert: 19.04.2015, 07:14
Wohnort: Bretagne (France)
Kontaktdaten:

Re: [restoration] L319D - 1958

Beitragvon panzerjim » 26.09.2016, 18:32

i use this one :

Bild

i always used it on chassis on my 4L, estafette, etc .... and never had problem :)
we can't make new with old .... but we try 8)

Benutzeravatar
panzerjim
Beiträge: 222
Registriert: 19.04.2015, 07:14
Wohnort: Bretagne (France)
Kontaktdaten:

Re: [restoration] L319D - 1958

Beitragvon panzerjim » 01.10.2016, 21:38

today i continue cleaning and painting :

Bild

Bild

Bild

the piece wainting remounting ... i have to make the silent bloc gum because those in place are dead ! :scheinheilig:

Bild

see you !! :top:
we can't make new with old .... but we try 8)

Benutzeravatar
panzerjim
Beiträge: 222
Registriert: 19.04.2015, 07:14
Wohnort: Bretagne (France)
Kontaktdaten:

Re: [restoration] L319D - 1958

Beitragvon panzerjim » 04.10.2016, 20:02

hi everybody !

i'm searching a website where i can buy these gummy parts :

Bild

i need :
8 with these sizes : 34mm diameter exterior , 10mm high and 14mm diameter interior.
8 with sizes : 34mm diam ext , 24mm hauteur et 12mm int
2 with sizes : 55mm length, 35mm diam ext et 24mm diam int with a plate face

thanks by advance !
Zuletzt geändert von panzerjim am 06.10.2016, 20:29, insgesamt 1-mal geändert.
we can't make new with old .... but we try 8)

Benutzeravatar
Brad
Beiträge: 64
Registriert: 28.05.2007, 08:54
Wohnort: Australia

Re: [restoration] L319D - 1958

Beitragvon Brad » 06.10.2016, 14:17

Which rubbers come from which parts?

Some of the front sway bar rubbers are similar size to the W120 MB-Ponton.

Benutzeravatar
panzerjim
Beiträge: 222
Registriert: 19.04.2015, 07:14
Wohnort: Bretagne (France)
Kontaktdaten:

Re: [restoration] L319D - 1958

Beitragvon panzerjim » 06.10.2016, 20:27

panzerjim hat geschrieben:
i need :
8 with these sizes : 34mm diameter exterior , 10mm high and 14 mm diameter interior. ==> radiator suspension
8 with sizes : 34mm diam ext , 24mm hauteur et 12mm int==> between stab bar and front axe
2 with sizes : 55mm length, 35mm diam ext et 24mm diam int with a plate face ==> stabilisator bar

thanks by advance !



remounting ... rim will be painted later

Bild

then, sanding and painting, i'll mount the brake after mouting the front axe on the body

Bild

Bild

to be continued tomorrow and saturday night
we can't make new with old .... but we try 8)

Benutzeravatar
Brad
Beiträge: 64
Registriert: 28.05.2007, 08:54
Wohnort: Australia

Re: [restoration] L319D - 1958

Beitragvon Brad » 07.10.2016, 11:37

panzerjim hat geschrieben:
panzerjim hat geschrieben:
i need :
8 with these sizes : 34mm diameter exterior , 10mm high and 14 mm diameter interior. ==> radiator suspension
8 with sizes : 34mm diam ext , 24mm hauteur et 12mm int==> between stab bar and front axe
2 with sizes : 55mm length, 35mm diam ext et 24mm diam int with a plate face ==> stabilisator bar

thanks by advance


Radiator support brackets? I just went to a suspension shop and bought some genric rubbers. The rubbers underneath the radiator are different again if I remember. They have a square hole. I just used a steel press and pressed a square hole.

http://www.mbclassics.de/index.php?a=3312&lang=eng .

Stabilisator-bar/front axel. I used MB rubbers for theses as they have a raised section. At the time, the MB part number is 1593230044. The steel retaining part for the rubbers is 1593230067.

Stabilisator-bar rubbers. I havent found anything similiar as of yet :( .
Du hast keine ausreichende Berechtigung, um die Dateianhänge dieses Beitrags anzusehen.

Benutzeravatar
panzerjim
Beiträge: 222
Registriert: 19.04.2015, 07:14
Wohnort: Bretagne (France)
Kontaktdaten:

Re: [restoration] L319D - 1958

Beitragvon panzerjim » 08.10.2016, 08:13

thanks Brad !! i think i've found ! it looks like the same !

i've take one more time the size and for the bar it's 23mm int. so with the years of work, i think the size grows.

i'll try this item for the stab bar : http://www.mbclassics.de/index.php?a=2290&lang=eng , hope it will be good ! :)
we can't make new with old .... but we try 8)

Benutzeravatar
panzerjim
Beiträge: 222
Registriert: 19.04.2015, 07:14
Wohnort: Bretagne (France)
Kontaktdaten:

Re: [restoration] L319D - 1958

Beitragvon panzerjim » 08.10.2016, 21:51

here we go ! let's work !

today i've put the suspension leaf in place (I swear it weighs a ton this stuff .... I wonder how the engine was able to drag it all to Thenay in 2015 to the International 4L with its 1200km round trip)

Bild

the upper front axe was dry, setting up rubber and motor support:

Bild

is presented with the Fenwick!

Bild

and abracadabra !

Bild

Then the most difficult time, we raise the body with the Fenwick and a little pallet hoping not to distort the windscreen bay ..

Bild

Bild

after fighting 1:30 to align everyone and bolt the bazaar!

Bild

Bild

I return the grille just to see and find his mouth I missed:

Bild

after a day of hard work I go to drink (in fact I'm already there ... :kiff: )

Bild

Kenavo! (it means bye-bye in Breton, regional language :wink: )
we can't make new with old .... but we try 8)

Benutzeravatar
Brad
Beiträge: 64
Registriert: 28.05.2007, 08:54
Wohnort: Australia

Re: [restoration] L319D - 1958

Beitragvon Brad » 09.10.2016, 12:22

Hahaha thats cheating using a forklift :lol:
Nice work!

If you get stuck with anything during reassembly, I do have a workshop manual with most reference sections. Although a few pages are missing.

Benutzeravatar
panzerjim
Beiträge: 222
Registriert: 19.04.2015, 07:14
Wohnort: Bretagne (France)
Kontaktdaten:

Re: [restoration] L319D - 1958

Beitragvon panzerjim » 15.10.2016, 19:46

heute arbeit !

reassembly of the rear shocks absorber:

Bild

disassembly, cleaning, painting and installing the brake master cylinder and front lines:

Bild

Bild


cleaning the injection pump, not had time to mount, I have to find the instructions for the well stall the first time

Bild

gently remounting

Bild

to be continued
we can't make new with old .... but we try 8)

Benutzeravatar
schrat
Administrator
Beiträge: 674
Registriert: 16.08.2004, 18:01
Wohnort: Rheinland
Kontaktdaten:

Re: [restoration] L319D - 1958

Beitragvon schrat » 17.10.2016, 18:42

what a GREAT work! :D Beautiful!
I'm dreaming of doing it the same way with my 319 one day

Benutzeravatar
panzerjim
Beiträge: 222
Registriert: 19.04.2015, 07:14
Wohnort: Bretagne (France)
Kontaktdaten:

Re: [restoration] L319D - 1958

Beitragvon panzerjim » 06.11.2016, 10:08

working , always working :mrgreen:

painting exhausts pipes with high temperature pro quality paint ... I hope it will stay because at € 27 bomb ..... ouch! I forgot to take the rest of the line is also painted ..

Bild

Stripping + full cleaning + rests of the clutch housing:

Bild

in place :

Bild


reassembling the transmission !

Bild

Bild

and installation of newly received silent block which are provided at the base for a Mercedes W128. the shaft is thinner than 1 or 2mm .... hope it will not break!

Bild

tchao ! :kiss:
we can't make new with old .... but we try 8)


Antworten

Zurück zu „Restaurierungsdokumentationen und Reparaturanleitungen“

Wer ist online?

Mitglieder in diesem Forum: 0 Mitglieder und 3 Gäste